Opel fireplace manual

This adapter will attach to the liner with 3 stainless steel rivets provided and to the EXCEL chimney with 3 screws provided. Note: The installation manual should always be used for the precise planning and accurate installation of your fireplace. Based on overall firebox dimensions, EPA official firebox volume per certification testing is 2. All models can also be installed to operate using room air.

Depends primarily on wood quality, ambient air temperature and building heat loss. Compare all fireplaces. Register a product. Find a dealer near you. Dealer locator. Have a question? Visit the FAQ. Opel 2 Plus. See it burn. Find a dealer. Opel 2 Plus certification, specifications and documentation. Catalyst Care Tips: Burn natural wood only. Do not burn chemical chimney cleaners, chemically treated wood, driftwood, construction scrap or garbage in your unit. Prolonged high or low temperatures may shorten the life of your Opel catalyst.

Remove cooled ash from the face of the catalyst by brushing it gently with a soft bristle brush e. Vacuum use near the face of the catalyst to remove the remaining ash is permitted; however avoid direct contact with the catalyst unit.

Limit cleaning to the visible face of the catalyst only. Attempting to clean the individual catalyst openings may do more harm than good. Scrapers or hard bristle brushes are never recommended. Available Options.

Opel Louver Trim The Opel Louver Trim is a portrait style frame to cover the rough-cut edges of finishing around the opening of the upper louver on an Opel fireplace. Internal Blower The internal blower kit will increase the circulation of heated air in the room where the fireplace is installed. Central Heat Blower Kit The central heat blower kit enables the distribution of heat generated by the fireplace throughout many rooms and different floors using either dedicated ducts or the house central heating ducts.

Heat Dump The Heat Dump Kit contains all the parts necessary to circulate a moderate amount of heat from your fireplace to another room with a small fan. Rock Retainer Kit Opel This rock retainer kit will allow you to finish your Opel fireplace with thin non-supporting facing such as tiles. Compare all fireplaces and options. Documents and Specs. If major repairs are required to meet the above Existing chimney installation: conditions, a new chimney should be constructed.

If it is difficult to install rigid stainless on an existing chim- New chimney installation: ney, a listed stainless steel flex liner can be used. Special care is to be taken when installing the flexible liner. Page Framing In The enclosure walls can be framed with any suitable mate- follows: rials 2x4 or 2x6 studs, plywood, gypsum board, etc.

Page Spark Guard The area immediately in front of the fireplace must be pro- tected by a non-combustible material such as brick, tile, NOTE: if the Opel AP is installed on a concrete floor, the stone, or slate. The size FDHB5-N installed, there will be some increase in warm and shape of your home and how you intend to use your air movement to rooms serviced by the gravity vent. BEFORE fastening the controls with the 2 screws pro- Black vided, thread the supplied chain through the spare key- White hole in the draft control and attach a pendant to the end, Ground bare just like the chain that is beside it.

Let the chain down on Remove the ash pan, to do so, you will need to remove the plug from the inside of the firebox. Insert the handle into the control eye. Replace the primary air screen and the secondary air tube. You can now stand up the Opel AP again, then put back the refractory liners and the doors. Figure 18b: Installation of the catalytic kit Page Remote Venting R may be required.

These clearances must 2. Install the metal edging on each side of the doors, making sure that the edges fit nicely with the arch edge be maintained for your safety. Page 26 -top grill open 3. Remove the outer cover to the left, right, or both sides of the flue outlet, on the Opel AP. Cut the insulation to the size of the opening and remove the cover plate underneath it is taped in place.

Remove the cover left side only. However, no Central heat control hot air duct is to be connected to the return air of kit FDHC6 another central heating system. Page 31 If possible, use a meter to test for continuity between the fan leads. Please note that the capacitor will show no reading if it is tested with a meter. Figure 31 shows an example of a and the blower center see Figure P Draft control lever P Draft control assembly