I added one to mine. Comment Post Cancel. David Anderson. It's not hard to install it. This problem has been discussed on here in great depth in the past, and I don't recall that anyone has ever come up with a solution. For example, volume control in the V-series organs is upstream of the preamp, so you have to mix the Percussion signal with the main signal before the volume control if you want Percussion volume to track with the main audio signal. Sweet Pete.
Percussion OR vibrato chorus available on V series. Not both at once like a Bummer for playing jazz,even rock Black Magic Woman has both too. V series won't get you there. One at a time. Maybe you like chorus on your perc? Not this guy. FWIW, I'm working on that very issue.
Sweet Pete commented. Once ran the Roland SH through the M scanner. There are synth bass upper keys on a 45 RPM I recorded with that little mod. The signal chain of the older models allows that input. Too bad the perc can't be mixed 'post'. Adding an 'aux' in wasn't going to happen LOL. Replaces both the AO power transformer and rectifier tubes used in Hammond H, H, and H series organs. A protective fuse is included. Direct replacement for the AO power transformer used in the AO reverb amplifier.
This amplifier was used in many A and M organs. A replacement 1K 1W resistor and a protective fuse are included. Direct replacement for the AO power transformer used in all X organs. A protective fuse kit is included. The LBG is a reproduction of the original grommet used in the lower rotor bearings as well as in the idler spring assembly of many Leslie models.
Sold in packages of 10 only. Allows older two channel Leslie speakers like the and to function as single channel cabinets making them much easier to utilize with a wide variety of instruments. As originally manufactured, these older cabinets do not function acceptably with single channel full frequency range signals. The LIA-1 is an improved version of the original idler spring assembly.
A slightly oversized wheel helps provide longer operating life. LPL Lower 60 Hz pulley. Reproduction of the original pulley used to drive the lower rotor in the following Leslie models: , R, RV, V, , , , RV, , , , , Allows most single channel Leslie speakers to be driven by your portable organ, guitar, synthesizer or mixer.
Replaces the end blocks used on the upper or lower manual of standard Hammond consoles. Allows simple mounting of custom switches or controls in a location easily accessible to the organist. These thin fiberglass sheets are shaped to fit between the keyboards and case of standard Hammond consoles to prevent woodwork damage when raising or removing manuals. Exact replacements for the adhesive backed expression mats used on many Hammond organ expression pedals.
To insure proper adhesion, the old mat as well as its adhesive must be thoroughly removed. For later standard Hammond consoles such as the A series, B-3 and C Durable black finish with fine texture.
Complete with KBF-1 upstop felt and new black mounting screws. A cost effective alternative to removing and disassembling Hammond tone wheel generators when defective frequencies are encountered. Simple three wire installation. Generates a sine wave output of any tone wheel frequency. The GNR-1A has a built in power supply and will replace one frequency. The KBF-1 is an exact reproduction of the B-3 type upstop felt. An essential part of any Hammond console restoration or busbar lube job, it helps restore the "new feel" and quiet operation to the keyboard.
The KBF-2 is an exact reproduction of the B-3 type downstop felt. Exact replacement for the brown oval head mounting screws used to secure the music rack mounting base in standard tonewheel consoles.
Replaces missing or damaged originals. Set of 4 Click on photo for enlargement. The box is made from heavy gauge anodized aluminum and easily mounts under the generator shelf or other convenient location. The unit has both an overall output and one that is low pass filtered. The low pass output is useful when using a bass amp to reinforce the organ low end. A level control is provided to allow the output signal to be adjusted to match the amplifier input requirements.
OBX units may be used to replace damaged or missing outlet boxes as well as to upgrade older consoles not originally equipped with outlet boxes. Designed to be mounted on either side of the console, end to end multiple units , or in an inverted position for C style cases. The optional OBX-MTG mounting kit may be used to install the outlet boxes in A organs, cut downs, or other applications where mounting to a flat surface is desired.
Identical to the RSP-1, but without the switch holes and lettering. Useful for covering the reverb control opening in A organs and other custom applications. Machined from heavy gauge aluminum. Black anodized finish. Includes switch mounting hardware. Exact replacement for the small black oval head mounting screws used to secure switch plate. Replaces the following Hammond part numbers: Click on photo for enlargement. Reproductions of the thumb screws used to secure the back panels of later standard Hammond consoles.
Mounts in place of the lower left hand end block on standard Hammond consoles. Allows convenient rocker switch control of the tremolo function. Normally provided with a two position switch.
Also available with a three position switch for use with Leslies designed with a stop function. Two electrically isolated switch sections allow easy control of dissimilar Leslies with a single switch. Pre-punched mounting hole provided for addition of a reverb or other control in the same enclosure.
0コメント